Comments on: Control ESP32/ESP8266 GPIOs from Anywhere (Firebase Web App)

By: Filipe Teixeira

Filipe Teixeira — Wed, 01 Oct 2025 02:03:56 +0000

Acabei de fazer este exercício completo e funciona corretamente, agora vou reler tudo de novo e personalizar um poco a pagina web e irei aplicar para controlar a iluminação do exterior da casa. Precisava era pelo menos de mais um canal, eu tenho 4 zonas distintas de iluminação exterior que queria controlar.

By: Sara Santos

Sara Santos — Thu, 31 Jul 2025 13:44:17 +0000

In reply to Ajith.

Where are you running the command?
Did you install the required software?
Make sure to check the Prerequisites section and follow everything under the section “Install Required Software”.
Regards,
Sara

By: Ajith

Ajith — Thu, 31 Jul 2025 12:47:57 +0000

Hi Sara,
While proceeding with this step(firebase login), I am facing error- The term ‘firebase’ is not recognized as the name of a cmdlet.

By: Sara Santos

Sara Santos — Mon, 07 Jul 2025 09:22:46 +0000

In reply to Ed.

That’s right!
Thanks for the tip.
Regards,
Sara

By: Ed

Ed — Sun, 06 Jul 2025 15:31:02 +0000

Just a tip: if at a certain point you only made changes in your html/JS/CSS/image files, instead of: “firebase deploy”, one can also use “firebase deploy –only hosting”
That goes a bit faster as it doesnt need to upload things like ‘rules’ etc

By: Sara Santos

Sara Santos — Sat, 18 Jan 2025 11:09:10 +0000

In reply to vijay sinh.

Hi.
Open the JAvascript console and see if you get any errors.
Also, hard refresh your web browser.
Regards,
Sara

By: vijay sinh

vijay sinh — Sat, 18 Jan 2025 10:37:59 +0000

In reply to Sara Santos. hi get everything fine also get web app successfully but there no any login form it just showing only title of web app and header

By: Arturo

Arturo — Fri, 08 Nov 2024 20:11:13 +0000

In reply to Sara Santos.

I get the following errors and have the same issue:

index.js:24 Uncaught SyntaxError: Identifier ‘dbPathOutput3’ has already been declared
auth.js:10 user logged out
subscribe.ts:239 ReferenceError: setupUI is not defined
at Object.next (auth.js:11:13)
at subscribe.ts:104:16
at subscribe.ts:233:11

By: Anbjørn Myren

Anbjørn Myren — Sun, 25 Aug 2024 21:38:16 +0000

In reply to Henry Leonardo Campos García.

Hi.
Its been a while since I set it all up so I dont remember every step in the process.
My setup is now with one NodeMCU receiver unit which have a 8 channel solidstate relay card connected so I can control 8 outputs.

I have 8 Wemos D1 Mini v3.0.0 with temp/humidity/pressure sensor that sends their values every 10 minute to the NodeMCU receiver. The NodeMCU compares the temperature value to check if it is higher or lower than the setpoint for the actual channel and sets the corresponding output on or off.

The NodeMCU also sends the values to the Firebase database, and also reads the setpoint values from the database. From the web-app webpage I can monitor all these 8 sensors and also change the setpoint values.
The NodeMCU also acts as a webserver, html code is nearly similar to the web-app, but it also have a timestamp so I can see when the values was last updated.

I did choose the Wemos boards for the sender units because their low standby power consumption, only about 8 microamp in deep standby. I set them to wake every 600 sec, transmit their value and return to deep sleep again. This way I can use 18650 3.7v batteries to power them and they lasts for months before recharge is needed.

By: Paulus Andi Nalwan

Paulus Andi Nalwan — Sat, 24 Aug 2024 03:42:56 +0000

Hi, I have reach step 18 but found error loading firebase SDK please check console. Could you let me know the solution?